In this video we build a blow gun and darts for less than $10! Step by step instructions and materials needed down below! Blowgun Materials needed: 2 3 foot sections of ½ inch, threaded PVC pipe 1 ½ inch threaded connector 1 ½ inch T joint 2 ½ inch plugs Steps: 1) Screw the T joint into the end of the first length of pipe 2) Attach the connector into the other end 3) Insert the 2 plugs into the sides of the T joint 4) Cut second length of pipe in half (make sure to not leave behind any of the plastic shavings after the cut. Sand the area down and rinse off) 5) Drill a hole in the top of the T joint to serve as a mouthpiece. (use a file and sandpaper to clean off the shavings) 6) Take second length of pipe that was already cut and attach to the connector Darts Materials needed: Some sort of thin metal rod. Options include: Bike wheels spokes, umbrella spokes, or insulation support wires. In the video we used the insulation support wires. Pillow stuffing or alpaca fur. Something fluffy that will hold together well. We used pillow stuffing in the video. Super glue Thread Steps: 1) Cut the metal rods to desired length 2) Sharpen one end of the darts by hammering it flat and then using a metal file to fine tune the edge. 3) Apply a small amount of super glue about 2 inches from the back of the dart 4) Run the back of the dart through the stuffing to the point where the glue is. Make sure the stuffing makes good contact with the glue and is well adhered to the metal. 5) Work towards the back of the dart adding more glue and adhering more stuffing until you reach the end. 6) Take the thread and wrap it around the base of the stuffing many times by spinning the dart in your fingers. After the thread is well and secure, run a single thread up and around the length of the fletching. When this single thread reaches the end of the fletching use a small drop of super glue to secure the thread in place and then cut. 7) Coat the spool of thread at the base of the fletching with a healthy amount of super glue. When this dries this will protect the thread and make it stronger, giving it a kind of armor coating. Subscribe if you liked this and share with somebody! Check out our website! http://fortinthewoods.com/ Our Patreon https://www.patreon.com/FortInTheWoods Follow us on Instagram:https://www.instagram.com/fort_in_the_woods/ Like and follow us on Facebook https://www.facebook.com/fortinthewoodsofficial/?ref=aymt_homepage_panel Amazon Affiliate Links Below: Some of the tools we used: Video Filmed with: Canon Rebel T5i: https://amzn.to/2st3jVg Rode VideoMic Rycote Lyre: https://amzn.to/2SSduOv The Fort In The Woods channel! https://www.youtube.com/channel/UCTY_WdjSdLj7NWWoo_c1sJw https://www.youtube.com/watch?v=BF9sm7npKPs

See us destroy a fort with a homemade PVC air cannon. We collaborate with Jake at the Jake Makes channel to see who builds the best backyard launcher. Watch us building a PVC pipe cannon with 2x4s, and leaf blowers! We test it by sending pool balls, smashing through our plywood target. Vote for the best launcher and help us win! Go watch Jakes video here https://www.youtube.com/watch?v=_oQ7rkhDOhY&feature=youtu.be&ab_channel=JakeMakes Leave a comment and let him know ours is better! Subscribe to Jakes channel for crazy builds and projects! Subscribe to Fort in the Woods for Trebuchets, forts, and more! Mark Rober's Snowball Machine Gun video, https://www.youtube.com/watch?v=JinpVA6p8Mo&t=147s&ab_channel=MarkRober Check out our website! http://fortinthewoods.com/ Our Patreon https://www.patreon.com/FortInTheWoods Follow us on Instagram:https://www.instagram.com/fort_in_the_woods/ Like and follow us on Facebook https://www.facebook.com/fortinthewoodsofficial/?ref=aymt_homepage_panel

Arrows can be a lot of fun for target practice or even just carrying while on adventures. Making arrows your self can be a enjoyable and makes it less upsetting when you lose them in the woods. Make your own arrows for less than $3! Using a few simple ingredients like string, tape, and some sort of PVC box I was able to make some pretty awesome arrows that worked super well. Try this one out yourself! Be careful and respect the tool you build. Check out our website! http://fortinthewoods.com/ Our Patreon https://www.patreon.com/FortInTheWoods Follow us on Instagram:https://www.instagram.com/fort_in_the_woods/ Like and follow us on Facebook https://www.facebook.com/fortinthewoodsofficial/?ref=aymt_homepage_panel Amazon Affiliate Links Below: Video Filmed with: Canon Rebel T5i: https://amzn.to/2st3jVg Rode VideoMic Rycote Lyre: https://amzn.to/2SSduOv The Fort In The Woods channel! https://www.youtube.com/channel/UCTY_WdjSdLj7NWWoo_c1sJw https://www.youtube.com/watch?v=qmzLiQscLHQ

In this weeks video we construct a Staff Sling to throw stuff really far. Have you ever wanted the ability to throw object incredible distances? We have (see our huge trebuchet in other videos) but we wanted something mobile. Using some simple materials we DIY a device that can sling large rocks across a field. For centuries the staff sling has been used to fight off wild animals, siege castle walls and even throw fiery object ship to ship on the high sea. It's easy to make, takes a little getting the hang of and while we don't recommend our build for maritime warfare we do recommend it for the yard. We suggest using tennis balls rather than rocks and also recommend using safety gear. Sling can release projectiles randomly if you don't have practice. Stay safe, have fun, find adventure and if you make something cool let us know! Check out our website! http://fortinthewoods.com/ Our Patreon https://www.patreon.com/FortInTheWoods Follow us on Instagram:https://www.instagram.com/fort_in_the_woods/ Like and follow us on Facebook https://www.facebook.com/fortinthewoodsofficial/?ref=aymt_homepage_panel

In this video Jacob builds a wooden round shield out of old palett slats and some scrap wood we had laying around the workshop. Check it out and share it with someone who might enjoy it! Subscribe if you haven't already! Check out our website! http://fortinthewoods.com/ Our Patreon https://www.patreon.com/FortInTheWoods Follow us on Instagram:https://www.instagram.com/fort_in_the_woods/ Like and follow us on Facebook https://www.facebook.com/fortinthewoodsofficial/?ref=aymt_homepage_panel Amazon Affiliate Links Below: Some of the tools we used: DeWALT cordless drill: https://amzn.to/2T1G6os Video Filmed with: Canon Rebel T5i: https://amzn.to/2st3jVg Rode VideoMic Rycote Lyre: https://amzn.to/2SSduOv The Fort In The Woods channel! https://www.youtube.com/channel/UCTY_WdjSdLj7NWWoo_c1sJw https://www.youtube.com/watch?v=eKBLfnhezC0

Check out our website! http://fortinthewoods.com/ In this video we build a wooden sword from an oak board, a branch from the woods, and a few rivets! Step by step directions!: 1. Measure two and a half hand lengths for the handle 2. Cut off end of board to use for handle pieces later 3. Take long block of wood and cut to desired length of cross guard 4. Cut cross guard block down the middle length ways to use later 5. Drill holes in each end of both cross guard pieces for the rivets 6. Cut handle piece down the middle length ways 7. Glue and clamp pieces to the handle portion of the sword 8. After glue dries plane and file corners off to round the handle 9. Shape blade by planning off the corners 10. Place the cross guard above the handle and rivet the ends together 11. Drill hole through middle of cross guard and the sword 12. Run rivet through the hole to secure the cross guard to the sword 13. Sand, oil, or otherwise decorate your sword as you see fit! Our Patreon https://www.patreon.com/FortInTheWoods Follow us on Instagram:https://www.instagram.com/fort_in_the_woods/ Like and follow us on Facebook https://www.facebook.com/fortinthewoodsofficial/?ref=aymt_homepage_panel Amazon Affiliate Links Below: Video Filmed with: Canon Rebel T5i: https://amzn.to/2st3jVg Rode VideoMic Rycote Lyre: https://amzn.to/2SSduOv The Fort In The Woods channel! https://www.youtube.com/channel/UCTY_WdjSdLj7NWWoo_c1sJw https://www.youtube.com/watch?v=JF0-s59K4x0

No blade is more famous than the curved samurai sword or katana from early Japanese history. We've made these for years and decided to recreate one from oak we glued together. This is an relatively easy DIY project as long as you have a few tools. Some clamps, a hand planer or even a knife, some sort of saw, and some sand paper. Glue and the wooden pieces should be all you need to be on your way to chopping some stuff. Check out our website! http://fortinthewoods.com/ Our Patreon https://www.patreon.com/FortInTheWoods Follow us on Instagram:https://www.instagram.com/fort_in_the_woods/ Like and follow us on Facebook https://www.facebook.com/fortinthewoodsofficial/?ref=aymt_homepage_panel https://www.youtube.com/channel/UCTY_WdjSdLj7NWWoo_c1sJw https://www.youtube.com/watch?v=kDBoxmrwclA

Check out our website! http://fortinthewoods.com/ Follow us on Instagram:https://www.instagram.com/fort_in_the_woods/ Like and follow us on Facebook https://www.facebook.com/fortinthewoodsofficial/?ref=aymt_homepage_panel Amazon Affiliate Links Below: Video Filmed with: Canon Rebel T5i: https://amzn.to/2st3jVg Rode NT1-A Condenser Mic: https://amzn.to/2D9c0tH The Fort In The Woods channel! https://www.youtube.com/channel/UCTY_WdjSdLj7NWWoo_c1sJw https://www.youtube.com/watch?v=5UnMlfvglE8